Getting Started with BPI-W3

Introduction

Banana Pi BPI-R1 Allwinner A20

Banana Pi BPI-R2 with MTK MT7623N chip design

Banana Pi BPI-R2 Pro Rockchip RK3568 design

Banana Pi BPI-R64 MTK MT7622

Banana Pi BPI-W2 with Realtek RTD1296 chip design

Banana Pi BPI-R3 with MediaTek MT7986(Filogic 830)

Banana Pi BPI-M2S Amlogic A311D chip

Linux

The below steps is to flash linux release image into BPI-W3

Prepare

1. Good Type-C data cable for image download into EMMC

2. Usb to ttl cable if you need debug, default baudrate is 1500000.

3. Windows or Linux PC.

4. Download the Linux Release Image Linux Release Image, and confirm that the md5 checksum is correct before flashing.

Note: The below picture is for BPI-W3's Debug Connecting, the blue usb cable is Double male USB data cable for image download, the white MicroUSB cable is linux serial console, please install CH340E's USB convert serial driver.

Install Whole Image with Usb Download Tool

Windows Driver install

1. Download and install Rockchip USB driver

File:Driver install.PNG

2. Download Rockchip USB Download Tool for EMMC upgrade

This tool defaults language is Chinese. you can change it to English after extract the package. Open RKDevTool_Release_v2.84/config.ini with an text editor (like notepad). The starting lines are:

 #Language Selection: Selected=1(Chinese); Selected=2(English)
 [Language]
 Kinds=2
 Selected=2
 LangPath=Language\

3. Open RKDevTool.exe, Switch to the “upgrade firmware” page. Press the “firmware” button to open the image file to be upgraded. The upgrade tool displays detailed firmware information.

  Note: Because Linux's release image is very large, So you need wait for a long time when Software open and analysis the image file.

4. Disconnect power adapter, connect dual male usb cable from the top usb host port to PC.

5. There have two usb download mode for image upgrade.

• Uboot Usb Download Mode (loader mode)

It's supposed to use this way if board already flashed a bootable uboot before.

• Maskrom Usb Download Mode

Press the Recovery button or Maskrom button beside 3pin uart header and hold, connect the power adapter or press the RST button if power adapter already connected, about two seconds later, release the button. PC will Identify the device if RK usb driver installed correctly.

The download tool also show the download mode if device connected.

6. Press the “upgrade” button to start the upgrade.

7: If the upgrade fails, you can try to erase the Emmc by pressing the EraseFlash button first, and then upgrade image again.

Install Separate Images with Usb Download Tool

1. Download Rockchip USB Download Tool for EMMC upgrade 2. Open RKDevTool.exe, Switch to the “Download Image” page. The upgrade tool displays detailed all firmware image information. Then all image file is ready, you may push "run", the upgrade process begin.

  Note: Because Linux's release package, Example: Ubuntu-22.04-Desktop-EMMCBoot-rockdev-MT7531SW-DSA.zip, unzip it into the same folder "Update-EMMC-Tools" inside.

Install Image with SDcard

1. Download Rockchip SDDiskTool.

2. Insert microSD card to Windows PC, 8GB sdcard size at least.

3. Run SD_Firmware_Tool, check the “Upgrade Firmware” box and select the correct removable disk device, Choose firmware image, then Click Create button to make it and wait until it is finshed

4. Safely remove the microSD card, insert it into the R2pro board, power on the board, it will start Linux System.

Build Linux BSP Source Code

1. Get Linux source code

 $ git clone https://github.com/BPI-SINOVOIP/BPI-R2PRO-BSP.git

2. Build the Linux BSP Source code

Dual Display

  Note: All linux Image suuport dual display HDMI and MIPI-DSI together, MIPI-DSI only support 1200x1920.
  Note: HDMI Display

  Note: MIPI-DSI panel Display

Wlan&BT

CN13 M.2 KEY E Slot is used for connect Wlan&BT adapter, default image support RTL8822CE(PCIE+USB) and RTL8822CS(SDIO+UART).