Difference between revisions of "Getting Started with BPI-M5"

From Banana Pi Wiki
Jump to: navigation, search
(Linux Server Image Network Configuration)
(Linux Wifi AP mode)
Line 546: Line 546:
 
  $ sudo apt install network-manager
 
  $ sudo apt install network-manager
  
:A simple 2.4G wifi ap mode netplan configuration file, 01-wlan0-ap-2.4g.yaml
+
:A sample 2.4G wifi ap mode netplan configuration file, 01-wlan0-ap-2.4g.yaml
 
  network:
 
  network:
 
  version: 2
 
  version: 2
Line 562: Line 562:
 
             password: "123456789"
 
             password: "123456789"
  
:A simple 5G wifi ap mode netplan configuration file, 01-wlan0-ap-5g.yaml
+
:A sample 5G wifi ap mode netplan configuration file, 01-wlan0-ap-5g.yaml
 
  network:
 
  network:
 
  version: 2
 
  version: 2

Revision as of 23:17, 2 February 2021

Introduction

Amlogic S905X3 Processor

Banana Pi M5 is a new generation single board computer design , use Amlogic S905X3 Quad-Core Cortex-A55 (2.0xxGHz) Processor. Mali-G31 MP2 GPU with 4 x Execution Engines (650Mhz). support 4GB LPDDR4 and 16G eMMC flash. it have 4 USB 3.0 port,1GbE LAN port.

specifications

  • SoC – Amlogic S905X3 quad-core Cortex-A55 processor @ up to 2.0 GHz with
  • Mali-G31 MP2 GPU @ 650Mhz
  • System Memory – 4GB LPDDR4
  • Storage – 16GB eMMC flash (option up to 64GB), MicroSD slot up to 2TB
  • Video Output – HDMI 2.1 up to 4Kp60 with HDR, CEC, EDID
  • Audio – 3.5mm audio jack, digital HDMI audio
  • Connectivity – Gigabit Ethernet
  • USB – 4x USB 3.0 ports via VL817 hub controller, 1x USB-C port (for power only?)
  • Expansion – 40-pin Raspberry Pi header with 28x GPIO, UART, I2C, SPI, PWM, and power signal (+5V, +3.3V, GND).
  • Debugging – 3-pin debug header
  • Misc – Reset, Power, and U-boot button; power and activity LED’s; IR receiver
  • Power Supply – 5V @3A via USB Type-C port
  • Dimensions – 92x60mm (Not the same as Raspberry Pi PCB size, but they probably included the connectors during measurement)
  • Weight – 48grams

development

Prepare

1. Prepare a usb-serial cable, a 5V/2A adaptor with type-c power supply. The serial cable is used for console debug and type-c cable is used for android image download and ADB debug.
2. Prepare a SDcard at least 8GB for linux development, android only support emmc boot.
3. The SOC rom first boot media is emmc, so board can't bootup from SDcard if the emmc is bootable with any image flashed, more info please refer to board boot sequence.
4. In Android SDcard is mmc0, emmc is mmc1, but in Linux SDcard is mmc1, emmc is mmc0.

Android

Prepare

1. Download and install the AML Usb Burning Tool for android image download via type-c, only support windows.
2. Download the latest android image, and confirm that the md5 checksum is correctly.

Install Image with Usb Burning Tool

1. Open USB_Burning_Tool.exe, select menu File->Import image, choose the android image file aml_upgrade_package.img.
M5 android install 1.png


2. M5 board disconnect power, press and hold SW4 button beside 40pin header, plugin type-c usb cable to PC
M5 android install 2.png


3. Click the Start button and wait for upgrade complete.
M5 android install 3.png


4. After Burning successfull, Unplug the type-c usb and connect to power supply adaptor to startup.
M5 android install 4.png


5. Click the Stop button to cancel the upgrade process and close the USB Buring Tool.

Build Android Source Code

1. Get Android 9.0 source code
 $ git clone https://github.com/BPI-SINOVOIP/BPI-S905X3-Android9
2. Build the Android 9.0 Source code
Please read the source code README.md

Android DTB overlay

Bananapi M5 DTBO idx value table, default idx value is 0 in release image.
Bananapi M5 DTBO idx value table
idx value device tree overlay description
0 android_p_overlay default dtbo, no use
1 wifi_bt_rtl8822cs enable bpi rtl8822cs wifi/bt module
2 i2c2 enable i2c 2
3 i2c3 enable i2c 3
4 sdio enable sdio
5 uart1 enable 2 pins uart 1
6 uart1_cts_rts enable 4 pins uart 1
7 uart2 enable 2 pins uart 2
8 hifi_pcm5122 enable i2s pcm5122 HiFi DAC
How to apply a new dtbo
1. ADB command via sysfs
 [email protected]:/tmp# adb root
 restarting adbd as root
 [email protected]:/tmp# adb remount
 remount succeeded
 [email protected]:/tmp# adb shell
 bananapi_m5:/ # echo dtbo > /sys/class/unifykeys/name                                                
 bananapi_m5:/ # echo "1" > /sys/class/unifykeys/write                                                
 bananapi_m5:/ # reboot
2. Uart console command via sysfs
 console:/ $ 
 console:/ $ su
 console:/ # echo dtbo > /sys/class/unifykeys/name                              
 [  [email protected]] unifykey: name_store() 1302, name dtbo, 4
 [  [email protected]] unifykey: name_store() 1311
 console:/ #
 console:/ # echo "1" > /sys/class/unifykeys/write                              
 [  [email protected]] unifykey: write_store()  is a string
 [  [email protected]] unifykey: dtbo, 1, 1
 [  [email protected]] unifykey: amlkey_write 393
 [  [email protected]] emmc_key_write:149, write ok
 console:/ # 
 console:/ # reboot
3. Settings App(To-Do)


Check the bootup uart debug message and confirm which dtbo is loaded actually, here "1" means set idx=1 to apply wifi_bt_rtl8822cs dtbo.
 load dtb from 0x1000000 ......
       Amlogic multi-dtb tool
       Single dtb detected
 find 2 dtbos
 dtbos to be applied: 1
 Apply dtbo 1
Unifykeys is stored in a specific emmc part, "Normal erase" selected in USB_Burning_Tool will not erase this data for next update, you must select "Erase all" if you want the default dtbo idx to be applied after image download.
M5 android erase all.png


Build Android image with a specific DTBO default.
1. Default build-in overlays are defined in device/amlogic/bananapi_m5/Kernel.mk, you can add a new overlay dtbo here.
 DTBO_DEVICETREE := android_p_overlay wifi_bt_rtl8822cs i2c2 i2c3 sdio uart1 uart1_cts_rts uart2 hifi_pcm5122
2. Default apply DTBO idx is defined in device/amlogic/bananapi_m5/BoardConfig.mk, you can change the idx value to set which overlay dtbo will be applied default.
 BOARD_KERNEL_CMDLINE += androidboot.dtbo_idx=0
3. DTS files are in common/arch/arm/boot/dts/amlogic/overlay/bananapi_m5/
More info about android device tree overlays, please refer to google android offical site

Linux

Prepare

1. Linux image support SDcard or EMMC bootup, but you should read the boot sequence at first.
2. Make sure bootable EMMC is formatted if you want bootup from SDcard, more info refer to Erase EMMC for SDcard Bootup
3. Make sure SDcard is formatted without Linux image flashed if you want bootup from EMMC and use Sdcard as storage.
4. Install bpi-tools on your Linux PC. If you can't access this URL or any other install problem, please go to bpi-tools source repo, download and install this tools manually.
 $ apt-get install pv
 $ curl -sL https://github.com/BPI-SINOVOIP/bpi-tools/raw/master/bpi-tools | sudo -E bash
5. Download Linux latest Linux Image, and confirm that the md5 checksum is correctly.
6. Default login: pi/bananapi or root/bananapi

Install Image to SDcard

1. Install image with bpi-tools on Linux, plug SDcard to Linux PC and run
 $ sudo bpi-copy xxx-bpi-m5-xxx.img.zip /dev/sdX
2. Install Image with dd command on Linux, umount SDcard device /dev/sdX partition if mounted automatically. Actually bpi-copy is the same as this dd command.
 $ sudo apt-get install pv
 $ sudo unzip -p xxx-bpi-m5-xxx.img.zip | pv | dd of=/dev/sdX bs=10M status=noxfer
3. Install Image with Etcher on Windows, Linux and MacOS.
Balena Etcher is an opensource project by Balena, Flash OS images to SDcard and USB drive

Install Image to EMMC

1. Prepare a SDcard with Linux image flashed and bootup board with this SDcard.
2. Copy Linux image to udisk, plug the udisk to board and mount it.
3. Install with bpi-tools command
 $ sudo bpi-copy xxx-bpi-m5-xxx.img.zip /dev/mmcblk0
4. Install with dd command, umount mmcblk0p1 and mmcblk0p2 partition if mounted automatically. Actually bpi-copy is the same as this dd command.
 $ sudo apt-get install pv
 $ sudo unzip -p xxx-bpi-m5-xxx.img.zip | pv | dd of=/dev/mmcblk0 bs=10M status=noxfer
5. After download complete, power off safely and eject the SDcard.

Build Linux Source Code

1. Get the Linux bsp source code
 $  git clone https://github.com/BPI-SINOVOIP/BPI-M5-bsp
2. Build the bsp source code
Please read the source code README.md
3. If you want build uboot and kernel separately, please download the u-boot the kernel only, get the toolchains, boot script and other configuration files from BPI-M5-bsp

DTB overlay

1. DTB overlay is used for 40pin gpios multi-function configuration and install in vfat BPI-BOOT/overlays
 [email protected]:~# ls /media/pi/BPI-BOOT/overlays/
 custom_ir.dtbo      pwm_b-backlight.dtbo  spi0.dtbo
 ds3231.dtbo         pwm_c-beeper.dtbo     uart1_cts_rts.dtbo
 hifi_pcm5102a.dtbo  pwm_cd-c.dtbo         uart1.dtbo
 hifi_pcm5122.dtbo   pwm_cd.dtbo           uart2.dtbo
 i2c0.dtbo           pwm_ef.dtbo           waveshare_tft24_lcd.dtbo
 i2c1.dtbo           pwm_ef-f.dtbo         waveshare_tft35c_lcd.dtbo
 pwm_ab.dtbo         sdio.dtbo             waveshare_tft35c_rtp.dtbo
2. Update the overlays env in vfat BPI-BOOT/boot.ini to enable what you want. Default i2c0, spi0 and uart1 enabled.
 # Overlays to load
 # Example combinations:
 #   spi0 i2c0 i2c1 uart0
 #   hktft32
 #   hktft35
 setenv overlays "i2c0 spi0 uart1"
3. Must be restart the board for overlay dtb loaded.

WiringPi

Note: This WiringPi only support set 40pin gpio to output, input or software pwm, for io functions as i2c, spi, pwm..., you must enable dtb overlay in boot.ini
1. Build and install wiringPi
 $ git clone https://github.com/BPI-SINOVOIP/amlogic-wiringPi
 $ cd amlogic-wiringPi
 $ chmod a+x build
 $ sudo ./build
2. Run gpio readall to show all 40pins status.

M5 wiringpi.png

3. BPI GPIO Extend board and examples in amlogic-wiringPi/examples
blinkall, blink all pin header gpios, no extend board.
lcd-bpi, BPI LCD 1602 display module example.
52pi-bpi, BPI OLED Display Module example.
matrixled-bpi, BPI RGB LED Matrix Expansion Module example.
berryclip-bpi, BPI BerryClip Module

Other Development

Linux uboot limit boot logo fb size to 1080p60hz/1920x1080 default, so oversize resolution will not be supported by default image, but you can modify uboot source code to support it.
1. Prepare a 24bit bmp file and named boot-logo.bmp
2. Compress the bmp file to boot-logo.bmp.gz
 $ gzip boot-logo.bmp
3. copy the target file to BPI-BOOT partition of linux image
 $ cp boot-logo.bmp.gz /media/xxx/BPI-BOOT/

Android bootloader limit boot logo fb display size is 1080p60hz/1920x1080 default, and android kernel dtb partition table limit boot logo partition size to 16MB default .
1. Prepare a 24bit bmp file and named boot-logo.bmp
2. Compress the bmp file to boot-logo.bmp.gz
 $ gzip boot-logo.bmp
3. Download m5_android_bootlogo_tool.zip
4. Extract this tool
 $ unzip m5_android_bootlogo_tool.zip
 $ cd m5_android_bootlogo_tool/
 $ cp -a logo_img_files logo               //logo_img_files is the origin bootlogo resource in android source and copy from <android-source-dir>/devices/amlogic/bananapi_m5/log_img_files
 $ ls -l logo/
 -rwxr--r-- 1 dangku dangku 525054 Sep 25 16:54 bootup.bmp
 -rwxr--r-- 1 dangku dangku 525054 Sep 25 16:54 bootup_X3.bmp
 -rwxr--r-- 1 dangku dangku    184 May 19  2020 upgrade_bar.bmp
 -rwxr--r-- 1 dangku dangku 180072 May 19  2020 upgrade_error.bmp
 -rwxr--r-- 1 dangku dangku 180072 May 19  2020 upgrade_fail.bmp
 -rwxr--r-- 1 dangku dangku 180072 May 19  2020 upgrade_logo.bmp
 -rwxr--r-- 1 dangku dangku 180072 May 19  2020 upgrade_success.bmp
 -rwxr--r-- 1 dangku dangku    184 May 19  2020 upgrade_unfocus.bmp
 -rwxr--r-- 1 dangku dangku 180072 May 19  2020 upgrade_upgrading.bmp
5. Copy the boot-logo.bmp.gz
 $ cp boot-logo.bmp.gz logo/bootup.bmp
 $ cp boot-logo.bmp.gz logo/bootup_X3.bmp
6. Create target logo.img with img pack tool, the binary and related libs of m5_android_bootlogo_tool are copy from <android-source-dir>/out/host/linux-x86
 $ ./logo_img_packer -r logo logo.img
7. Flash boot logo with fastboot
 $ adb root
 $ adb remount
 $ adb reboot fastboot
Wait few seconds and check whether fastboot connected
 $ fastboot device
 1234567890      fastboot
 $ fastboot flashing unlock_critical
 $ fastboot flashing unlock
 $ fastboot flash logo logo.img
 $ fastboot reboot

Boot Sequence

M5 linux boot squence.png
Check bootloader loaded from SDcard or EMMC at the beginning of the console debug messages
1. Rom load bootloader from SDcard (Linux log example)
 ...
 
 BL2 Built : 15:21:42, Mar 26 2020. g12a g486bc38 - [email protected]
 
 Board ID = 1
 Set cpu clk to 24M
 Set clk81 to 24M
 Use GP1_pll as DSU clk.
 DSU clk: 1200 Mhz
 CPU clk: 1200 MHz
 Set clk81 to 166.6M
 board id: 1
 Load FIP HDR DDR from SD, src: 0x00010200, des: 0xfffd0000, size: 0x00004000, part: 0
 fw parse done
 PIEI prepare done
 fastboot data verify
 result: 255
 Cfg max: 12, cur: 1. Board id: 255. Force loop cfg
 DDR4 probe
 
 ...
2. Rom load bootloader from EMMC(Android Log example)
 ...
 
 Board ID = 1
 Set cpu clk to 24M
 Set clk81 to 24M
 Use GP1_pll as DSU clk.
 DSU clk: 1200 Mhz
 CPU clk: 1200 MHz
 Set clk81 to 166.6M
 eMMC boot @ 0
 sw8 s
 board id: 1
 Load FIP HDR DDR from eMMC, src: 0x00010200, des: 0xfffd0000, size: 0x00004000, part: 0
 fw parse done
 PIEI prepare done
 00000000
 emmc switch 1 ok
 ddr saved addr:00016000
 Load ddr parameter from eMMC, src: 0x02c00000, des: 0xfffd0000, size: 0x00001000, part: 0
 00000000
 
 ...

Erase EMMC for SDcard Bootup

There are four possible scenarios should be pay attention to, EMMC already flashed Android image, EMMC already flashed Linux image, boot process hangup in BL2 and EMMC empty.
1. Bootable EMMC with Android image flashed
a). Using usb burning tool, unplug the type-c usb cable while the download process at 7% formatting
M5 android format.png
b). Using Android Fastboot tool, make sure the adb/fastboot tools is work on your PC before doing this.
   [email protected]:/tmp# adb root
   adbd is already running as root
   [email protected]:/tmp# adb remount
   remount succeeded
   [email protected]:/tmp# adb shell
   bananapi_m5:/ # reboot fastboot
Wait a few seconds for board reboot to fastboot mode
   [email protected]:/tmp# fastboot devices
   1234567890	fastboot
   [email protected]:/tmp# fastboot flashing unlock_critical
   ...
   OKAY [  0.044s]
   finished. total time: 0.044s
   [email protected]:/tmp# fastboot flashing unlock
   ...
   OKAY [  0.047s]
   finished. total time: 0.047s
   [email protected]:/tmp# fastboot erase bootloader
   erasing 'bootloader'...
   OKAY [  0.059s]
   finished. total time: 0.059s
   [email protected]:/tmp# fastboot erase bootloader-boot0
   erasing 'bootloader-boot0'...
   OKAY [  0.036s]
   finished. total time: 0.036s
   [email protected]:/tmp# fastboot erase bootloader-boot1
   erasing 'bootloader-boot1'...
   OKAY [  0.035s]
   finished. total time: 0.035s
c). Using uboot command, connect a debug console cable and press ESC while power on to enter uboot command line
   bananapi_m5_v1#amlmmc erase 1
   emmckey_is_protected(): protect
   start = 0,end = 57343
   start = 221184,end = 30535679
   Erasing blocks 0 to 8192 @ boot0
   start = 0,end = 8191
   Erasing blocks 0 to 8192 @ boot1
   start = 0,end = 8191
   bananapi_m5_v1#reset
   resetting ...
   SM1:BL:511f6b:81ca2f;FEAT:A0F83180:20282000;POC:F;RCY:0;EMMC:0;READ:0;CHK:1F;READ:0;CHK:1F;READ:0;CHK;
These two ways actually erase the bootloader part of EMMC android, After bootup from SDcard Linux, You'd better format the whole EMMC by dd command.
d). Using uboot reboot command to restart from SDcard once time, but Android in EMMC still exist completely. Connect a debug console cable and press ESC while power on to enter uboot command line, type "reboot sdboot" command, After reboot from SDcard Linux, you can format the whole EMMC by dd command and then flash the Linux image to EMMC.
   bananapi_m5_v1#
Insert the SDcard with Linux image flashed now.
   bananapi_m5_v1#reboot sdboot
   reboot mode: sdboot
   reboot dev: sd
   BPI: set rom boot from sdcard after reset
   before value = 0!
   after value = 4f5244c0!
   resetting ...
   SM1:BL:511f6b:81ca2f;FEAT:A0F83180:20282000;POC:F;RCY:0;OVD:2;SD?:0;SD:0;READ:0;0.0;CHK:0;
   bl2_stage_init 0x01
   ...
   board id: 1
   Load FIP HDR DDR from SD, src: 0x00010200, des: 0xfffd0000, size: 0x00004000, part: 0
   ...
e). The simplest way is insert the SDcard with Linux image flashed before power on, the Android bootloader will check boot.ini file whether exist in SDcard vfat partition, so that the SDcard Linux will bootup. After bootup, you can format the whole EMMC by dd command and then flash the Linux image to EMMC.
   ...
   BPI: try boot from sdcard
   reading boot.ini
   5699 bytes read in 3 ms (1.8 MiB/s)
   ## Executing script at 01b00000
   ...
   reading Image.gz
   9143358 bytes read in 510 ms (17.1 MiB/s)
   reading meson64_bananapi_m5.dtb
   70850 bytes read in 8 ms (8.4 MiB/s)
   reading uInitrd
   11704481 bytes read in 655 ms (17 MiB/s)
   reading overlays/i2c0.dtbo
   223 bytes read in 6 ms (36.1 KiB/s)
   reading overlays/spi0.dtbo
   516 bytes read in 6 ms (84 KiB/s)
   reading overlays/uart1.dtbo
   225 bytes read in 5 ms (43.9 KiB/s)
2. Bootable EMMC with Linux image flashed
a). Using uboot command, connect a debug console cable and press ESC while power on to enter uboot command line
   bananapi_m5# mmc erase 0 1000
b). Linux u-boot also check boot.ini file whether exist in SDcard vfat partition so that the SDcard Linux will bootup. After bootup, you can format the whole EMMC by dd command or flash the Linux image directly to EMMC.
3. A extreme situation is bootloader or uboot corrupted, Rom load it from EMMC but hangup in u-boot or BL2, for example the boot process will hangup in BL2 of EMMC if dram init failed, The only way is format the EMMC with usb burning tool, or download the Android image completely and then try other ways to erase EMMC or flash Linux image to EMMC.
4. Rom will try to load bootloader from SDcard directly if EMMC is empty.

Erase Emmc Android by dd command

If the board is flashed android before, the whole emmc must be erased by these commands if you want bootup it with SDcard Linux image.
 $ sudo dd if=/dev/zero of=/dev/mmcblk0boot0 bs=1M status=noxfer 
 $ sudo dd if=/dev/zero of=/dev/mmcblk0boot1 bs=1M status=noxfer
 $ sudo dd if=/dev/zero of=/dev/mmcblk0 bs=1M status=noxfer 
 $ sync

Wifi/BT support

1. Android test and support.
 rtl8723bu wifi/bt(usb)
 rtl8188eu wifi(usb)
 rtl8822cs wifi/bt(sdio/uart)
How to enable Android Wifi/BT
USB type: Plug-in the usb dongle to usb host port and reboot the system, After bootup, you can enable or disable wifi and bluetooth in Settings app.
SDIO/UART type: Connect the hardware module to 40pin header correctly and configure the Android DTB overlay to enable it.
Note: Android is not support that ethernet and wifi are both connected at the same time, Ethernet have a higher prioprity than wifi, it means wifi can't connect network if ethernet already connected, and wifi will drop connection if ethernet cable plugin.
2. Linux test and support.
 rtl8188eu wifi(usb)
 rtl8192eu wifi(usb)
 rtl8723bu wifi/bt(usb)
 rtl8811au wifi(usb)
 rtl8812au wifi(usb)
 rtl8812bu wifi(usb)
 rtl8822cs wifi/bt(sdio/uart)
How to enable Linux Wifi
Wifi module drivers are already prebuild in the release images.
USB type: Plug-in the usb dongle to usb host port and driver will be loaded automatically.
SDIO/UART type:
1). Connect the hardware module to 40pin header correctly.
2). Configure the dtb overlay
  # Overlays to load
  # Example combinations:
  #   spi0 i2c0 i2c1 uart0
  #   hktft32
  #   hktft35
  setenv overlays "wifi_bt_rtl8822cs"
3). Add the wifi module name to /etc/modules for loaded automatically next boot.
How to enable Linux Bluetooth
1). Please download rtk-linux-bt-driver source code, build and install usb or uart rtk linux bluetooth drivers/firmwares to your image.
2). For USB type, plug-in the usb dongle to usb host port and driver will be loaded automatically.
3). For UART type, Configure the dtb overlay as the same as wifi before install the bluetooth drivers/firmwares. hci_uart driver will be loaded when rtk-hciuart.service start.

Linux Server Image Network Configuration

Netplan
A sample wifi sta mode netplan configuration file, 01-wlan0-sta.yaml
network:
  version: 2
  renderer: networkd
  wifis:
    wlan0:
      dhcp4: true
      access-points:
        "bananapi":
           password: "123456789"

Linux Wifi AP mode

1. Prepare the setup the wifi adater correctly.
2. Get the wifi adapter Band, Frequencies, Channel, HT Capability, VHT Capability or other properties
$ iw list
3. Manage wifi access point mode with Netplan and Network-Manager.
Install NetworkManager because ap is only supported with NetworkManager renderer
$ sudo apt install network-manager
A sample 2.4G wifi ap mode netplan configuration file, 01-wlan0-ap-2.4g.yaml
network:
version: 2
renderer: NetworkManager
wifis:
  wlan0:
    dhcp4: no
    access-points:
      "bananapi":
         mode: ap
         band: 2.4GHz
         channel: 6
         auth:
           key-management: psk
           password: "123456789"
A sample 5G wifi ap mode netplan configuration file, 01-wlan0-ap-5g.yaml
network:
version: 2
renderer: NetworkManager
wifis:
  wlan0:
    dhcp4: no
    access-points:
      "bananapi":
         mode: ap
         band: 5GHz
         channel: 36
         auth:
           key-management: psk
           password: "123456789"
4. Manage wifi access point mode with Netplan and Hostapd.
1). Create a netplan configuration file, 01-wlan0-ap-hostapd.yaml
network:
version: 2
renderer: networkd
ethernets:
  wlan0:
    dhcp4: no
    addresses:
      - 192.168.11.1/24
2). Install hostapd
$ sudo apt install hostapd
Create hostapd configuration file /etc/hostapd/hostapd.conf, for example
interface=wlan0
ssid=bananapi

driver=nl80211

auth_algs=1
wpa=2
wpa_passphrase=123456789
wpa_key_mgmt=WPA-PSK
rsn_pairwise=CCMP

#bridge=br0
beacon_int=500
#SSID not hidden
ignore_broadcast_ssid=0

hw_mode=a
channel=149
max_num_sta=8

### IEEE 802.11n
ieee80211n=1
#require_vht=0
ht_capab=[HT20][HT40+][SHORT-GI-20][SHORT-GI-40][SHORT-GI-80][DSSS_CCK-40]

### IEEE 802.11ac
ieee80211ac=1
#require_vht=0
#vht_capab=[MAX-MPDU-3895][SHORT-GI-80][SU-BEAMFORMEE]
#vht_oper_chwidth=1
#vht_oper_centr_freq_seg0_idx=42

### WMM
wmm_enabled=1
3). To support 80MHz channel width you need load driver with rtw_vht_enable=2 option, Or you can create /etc/modprobe.d/8822cs.conf with content
options 88x2cs rtw_vht_enable=2
4). Install and configure dhcp server service, use isc-dhcp-server for example
$ sudo apt install isc-dhcp-server
Configure dhcp server interface in /etc/default/isc-dhcp-server
# On what interfaces should the DHCP server (dhcpd) serve DHCP requests?
#       Separate multiple interfaces with spaces, e.g. "eth0 eth1".
INTERFACESv4="wlan0"
Configure dhcp subnet and dns in /etc/dhcp/dhcpd.conf
...
option domain-name "example.org";
option domain-name-servers 8.8.8.8, 114.114.114.114;
...
# No service will be given on this subnet, but declaring it helps the 
# DHCP server to understand the network topology.
subnet 192.168.11.0 netmask 255.255.255.0 {
  range dynamic-bootp 192.168.11.1 192.168.11.100;
  option broadcast-address 192.168.11.255;
  option routers 192.168.11.1;
}
5). Start Service
$ sudo restart isc-dhcp-server
$ sudo hostapd /etc/hostapd/hostapd.conf -B
6). Routing configuration.
sysctl net.ipv4.ip_forward=1
iptables -t nat -A POSTROUTING -s 192.168.11.0/24 -o eth0 -j MASQUERADE

Coreelec

1. Get the source code.
 $ git clone https://github.com/Dangku/CoreELEC
2. Get the docker containner for source code build
More info refer to Coreelec official website and github