BPI-Bit-S2

About BPI-Bit-S2

BPI-Bit-S2 with ESP32-S2

BPI-Bit with ESP32

BPI-Leaf-S3 with ESP32-S3

BPI-AI Kendryte K210 RISC-V

BPI-UNO32 with ESP32 design

BPI-Bit-S2 development board is a successor to BPI-Bit, inheriting most of the hardware functions.

IO is compatible with micro:bit and can use most peripheral accessories of micro:bit.

Support Webduino, Arduino, MicroPython & CircuitPython programming environment suitable for STEAM education.

Key features

• ESP32-S2
• 5x5 RGB LED matrix
• 1 buzzer
• 1 thermistor sensor
• 2 photosensitive sensors
• 2 programmable keys,1 BOOT key,1 Reset key
• Type-C USB interface
• Size 5x5cm
• The Goldfinger Edge Connector definition is fully compatible with Micro: Bit

Feature comparison

micro:bit vs BPI-Bit-S2
Product	micro:bit V2.2X	BPI-Bit-S2
MCU	Nordic nRF52833	Espressif ESP32-S2
Frequency	64MHz	240MHz
RAM	128KB	320 KB
FlASH ROM	512KB	4096 KB
PSRAM	None	2048 KB
Wireless Communication	Bluetooth，microbit-radio	WIFI, IEEE 802.11 b/g/n, 2.4Ghz
LED	25 red LEDs	25 WS2812-3535 RGB LEDs
Key	2 programmable keys, 1 RST key	2 programmable keys, 1 BOOT key, 1 RST key
Buzzer	Yes	Yes
Microphone	Yes	None
USB Socket	Micro USB	Type-C USB
USB interface chip	nRF52833-QDAA or nRF52820-QDAA	MCU chip built-in
Battery socket	Yes	None
IO	19 pins golden finger IO, alligator clip bayonet, support touch sensing	19 pins golden finger IO (compatible with micro:bit), alligator clip bayonet, support touch sensing
Motion sensor	Yes	None
Photosensitive sensor	None	2
Thermistor sensor	1 on-core	1 on-board

Hardware interface

BPI-Bit-S2 specification
MCU	ESP32-S2FN4R2，Xtensa® 32 bit LX7 Single-Core Processer
Frequency	240MHz MAX
operating temperature	-40℃~+85℃
ROM	128 KB
SRAM	320 KB
FLASH ROM	4 MB
PSRAM	2 MB
WIFI	IEEE 802.11 b/g/n ，2.4Ghz
GPIO	19 available GPIO pins have been introduced
Peripheral functions	ADC,TOUCH,PWM,SPI,I2C,I2S,Pulse counter, RMT,TWAI® Controller,SD/MMC,LCD_CAMERA
External crystal	40Mhz
Buzzer	8.5x8.5mm buzzer
LED	25 WS2812 rgb LED, single line GPIO control; 1 monochrome LED, controlled by GPIO0
Photosensitive sensor	2 photosensitive sensor
Thermistor sensor	1 thermistor sensor
IO	19 pins Goldfinger IO,19 pins contacts on the back
Key	2 programmable keys,1 BOOT key,1 Reset key
USB	USB Type-C interface，full speed USB OTG,USB-ACM
Operating voltage	3.3V
Power	USB Type-C input 5V，or Goldfinger IO input 3.3V power supply
Size	5 * 5 cm

On-board peripherals

Peripheral GPIO allocation and signal type
Photosensitive sensor(L)	GPIO 12	Analog Input
Photosensitive sensor(R)	GPIO 13	Analog Input
Thermistor sensor	GPIO 14	Analog Input
Key A	GPIO 38	Digital Input
Key B	GPIO 33	Digital Input
Key BOOT	GPIO 0	Digital Input
Buzzer	GPIO 17	PWM(Digital Output)
RGB LEDs	GPIO 18	Digital Output

5*5 RGB LED

BPI-Bit-S2 have 25 WS2812 full color RGB LED, single GPIO ontrol.

The three primary color pixels of each LED can achieve 8bit 256 level brightness display,

and achieve 16777216 color full color display,

scanning frequency is not less than 400Hz/s.

5*5 LED Sequential List
20	15	10	5	0
21	16	11	6	1
22	17	12	7	2
23	18	13	8	3
24	19	14	9	4

Goldfinger GPIO define

BPI-Bit-S2 Gold finger GPIO is defined to be compatible with Micro:Bit. GPIO expansion board accessories can be used with Micro: Bit.

SPI,I2C
Function	Pin Name	GPIO Num
SPI_SCK	P13	GPIO36
SPI_MISO	P14	GPIO37
SPI_MOSI	P15	GPIO35
SPI_CS	P16	GPIO34
I2C_SCL	P19	GPIO16
I2C_SDA	P20	GPIO15

Power

BPI-Bit-S2 supports two power supply modes

1. Type-C USB：Use USB cable power supply, connect USB interface of computer or other 5V USB charger to power the development board.

2. Gold finger: At the bottom of the development board, the gold finger contains a power interface with both input and output functions. It uses 3.3V power supply, positive terminal is connected to 3V3, and negative terminal is connected to GND.

Software

Webduino

webduino online building block programming platform

webduino building block programming platform, Windows Installer

webduino online tutorials

MicroPython

MicroPython is a lean and efficient implementation of the Python 3 programming language that includes a small subset of the Python standard library and is optimised to run on microcontrollers and in constrained environments.

Crowdfunded and open sourced in 2013 by Damien P. George.

The most obvious difference between it and the use of C programs to develop microcontrollers is that there is no need for lengthy compilation when verifying code.

Using serial communication software, enter commands through the REPL(read-eval-print-loop) to control the microcontroller, just like Python's REPL.

It is also possible to use some tools to upload a python script file to run inside the microcontroller.

Its implementation of Python3 includes the _thread library that supports multithreading and the asyncio library for writing concurrent code.

MicroPython aims to be as compatible with normal Python as possible to allow you to transfer code with ease from the desktop to a microcontroller or embedded system.

At the same time it also has some libraries specific for microcontrollers in order to take full advantage of the hardware features inside the microcontroller chip, such as timers, hardware interrupts, WiFi, etc., depending on the specific hardware.

While having the above features, it is compact enough to fit and run within just 256k of code space and 16k of RAM.

If you know Python you already know MicroPython.

On the other hand, the more you learn about MicroPython the better you become at Python.

CircuitPython

CircuitPython is an education-friendly open source derivative of MicroPython, supported and developed by Adafruit Industries.

In terms of ease of use, it goes a step further on the basis of MicroPython.

When the development board using CircuitPython firmware is connected to the PC, the PC will immediately get a USB storage disk.

And the python script file can be copied to this disk to allow the program to run on the development board.

This allows users to use it out of the box, because most modern personal operating systems and home PCs support USB storage disks.

Of course, in order to use REPL, at least a serial communication software needs to be installed, or a text editor that supports this function, such as Mu editor.

The CircuitPython community provides an extremely rich peripheral driver library, APIs documentation, and tutorials.

Even if there is no programming foundation, no hardware foundation, you can quickly get started from scratch.

CircuitPython does not support some microcontroller-specific libraries such as timer and hardware interrupt, nor does it support the multi-threaded _thread library. It only provides the asyncio library for writing concurrent code.

The code is very portable between microcontrollers supported by CircuitPython and single-board computers (SBCs) supported by Blinka. This is thanks to its efforts to unify APIs.

Arduino

Arduino is an open source embedded hardware and software development platform for users to create interactive embedded projects.

• Arduino IDE download link | Install and configure Arduino-ESP32 running environment
• Arduino-ESP32 APIs

Documents

BPI-Bit Lite schematic