Code circuitpython with mu en - Revision history

Wind: /* Establish the connection */

2022-09-29T09:42:09Z

Establish the connection

← Older revision		Revision as of 09:42, 29 September 2022
Line 25:		Line 25:
	= Establish the connection =		= Establish the connection =

	2. Start the Mu editor and change the mode to '''CircuitPython''', if you have connected the CircuitPython development board correctly, you will be prompted whether to switch to this mode directly.		1. Start the Mu editor and change the mode to '''CircuitPython''', if you have connected the CircuitPython development board correctly, you will be prompted whether to switch to this mode directly.

	[[File:Download_mu_3.png \| 600px]]		[[File:Download_mu_3.png \| 600px]]
Line 31:		Line 31:
	[[File:Download_mu_4.png \| 400px]]		[[File:Download_mu_4.png \| 400px]]

	3. Click the '''Serial''' button and press any key to enter the CircuitPython REPL.		2. Click the '''Serial''' button and press any key to enter the CircuitPython REPL.

	[[File:Download_mu_5.png \| 600px]]		[[File:Download_mu_5.png \| 600px]]

Wind at 07:02, 29 September 2022

2022-09-29T07:02:47Z

← Older revision		Revision as of 07:02, 29 September 2022
Line 1:		Line 1:
	[[zh:~~Code_circuitpython_with_mu_cn~~]]		[[zh:Code_circuitpython_with_mu_ch]]

	= Hardware Preparation =		= Hardware Preparation =

Wind at 07:02, 29 September 2022

2022-09-29T07:02:26Z

← Older revision		Revision as of 07:02, 29 September 2022
Line 1:		Line 1:
			[[zh:Code_circuitpython_with_mu_cn]]

	= Hardware Preparation =		= Hardware Preparation =

Wind: /* Edit code.py to make the lights blink */

2022-09-29T06:49:59Z

Edit code.py to make the lights blink

← Older revision		Revision as of 06:49, 29 September 2022
Line 33:		Line 33:
	[[File:Download_mu_5.png \| 600px]]		[[File:Download_mu_5.png \| 600px]]

	= Edit code.py to make the ~~lights~~ blink =		= Edit code.py to make the LED blink =

	1. Click the '''Load''' button, select the code.py file on the CircuitPython development board, and click Open to start editing code.py .		1. Click the '''Load''' button, select the code.py file on the CircuitPython development board, and click Open to start editing code.py .

Wind: Created page with "= Hardware Preparation = 1. Mu editor supports Windows x64, Mac OSX, Linux operating systems, prepare a computer running one of these operating systems. 2. A development boa..."

2022-09-29T06:49:36Z

Created page with "= Hardware Preparation = 1. Mu editor supports Windows x64, Mac OSX, Linux operating systems, prepare a computer running one of these operating systems. 2. A development boa..."

New page

= Hardware Preparation =

1. Mu editor supports Windows x64, Mac OSX, Linux operating systems, prepare a computer running one of these operating systems.

2. A development board that supports CircuitPython, such as BPI-PicoW-S3.

3. A USB cable that can connect the development board to the computer.

= Download and install Mu Editor =

* [https://codewith.mu/ Mu editor official download page]

1. Open the Mu editor web page and click the '''Download''' button to enter the new page.

[[File:Download_mu_1.png | 600px]]

2. Select the operating system currently used by your computer, and click the '''Download''' button corresponding to the operating system to start downloading the installation package.

[[File:Download_mu_2.png | 600px]]

3. Click the '''Instuctions''' button of the corresponding operating system to view the detailed installation steps, and install according to the instructions.

= Establish the connection =

2. Start the Mu editor and change the mode to '''CircuitPython''', if you have connected the CircuitPython development board correctly, you will be prompted whether to switch to this mode directly.

[[File:Download_mu_3.png | 600px]]

[[File:Download_mu_4.png | 400px]]

3. Click the '''Serial''' button and press any key to enter the CircuitPython REPL.

[[File:Download_mu_5.png | 600px]]

= Edit code.py to make the lights blink =

1. Click the '''Load''' button, select the code.py file on the CircuitPython development board, and click Open to start editing code.py .

2. Enter the following code in the editor:

<pre>
import time
import board
import neopixel

pixels = neopixel.NeoPixel(board.NEOPIXEL, 1, brightness=0.1)

while 1:
pixels[0] = (255,0,0)
pixels.show()
time.sleep(0.5)
pixels[0] = (0,255,0)
pixels.show()
time.sleep(0.5)
pixels[0] = (0,0,255)
pixels.show()
time.sleep(0.5)
pixels[0] = (255,255,255)
pixels.show()
time.sleep(0.5)
</pre>

3. Click the '''Save''' button, and the edited content will be saved to the CircuitPython development board.

If the code is correct, the full color LED on the development board will twinkle red, green, blue, and white cyclically.