Sinovoip at 05:51, 27 October 2018

2018-10-27T05:51:12Z

Sinovoip: Created page with "en:Getting_Started_with_M64"

2018-10-27T05:50:34Z

Created page with "en:Getting_Started_with_M64"

New page

[[en:Getting_Started_with_M64]]

← Older revision		Revision as of 05:51, 27 October 2018
Line 1:		Line 1:
	[[en:Getting_Started_with_M64]]		[[en:Getting_Started_with_M64]]
		+
		+	=Introduction=
		+	==BPI-M64==
		+	[[File:M64_respbian.png\|thumb\|Overview: BPI-M64 respbian linux]]
		+
		+	Banana Pi BPI-M64 is a 64-bit quad-core mini single board computer. It features 2GB of RAM and 8GB eMMC. It also has onboard WiFi and BT. On the ports side, the BPI-M64 has 2 USB A 2.0 ports, 1 USB OTG port, 1 HDMI port, 1 audio jack, and lastly a DC power port. The processor is pin-to-pin comptialbe with R18, so it comes with two versions:M64 and M64-R18
		+
		+	*Read more about : [[Banana Pi BPI-M64]]
		+
		+	===A64 Key Features===
		+	* 1.2 Ghz Quad-Core ARM Cortex A53 64-Bit Processor-A64
		+	* 2GB DDR3 SDRAM
		+	* 8G EMMC
		+	* 10/100/1000Mbps Ethernet
		+	* WiFi (AP6212) & Bluetooth
		+
		+	===R18 Key Features===
		+	* 1.2 Ghz Quad-Core ARM Cortex A53 64-Bit Processor-R18
		+	* 2GB DDR3 SDRAM
		+	* 8G EMMC
		+	* 10/100/1000Mbps Ethernet
		+	* WiFi (AP6212) & Bluetooth
		+
		+	=Development=
		+	==Basic Development==
		+	===Prepare to develop===
		+	* Prepare 8G/above TF card, USB-Serial interface, PC with Ubuntu System
		+	* Using your USB-Serial Connect debug console on M64
		+
		+	===Load your first image on M64===
		+	1.You could download latest image from our forum
		+
		+	2.Install bpi-tools on your system
		+	* apt-get install pv
		+	* curl -sL https://github.com/BPI-SINOVOIP/bpi-tools/raw/master/bpi-tools \| sudo -E bash
		+
		+	3.After you download the image, insert your TF card into your Ubuntu
		+	* Execute "bpi-copy xxx.img /dev/sdx" to install image on your TF card.
		+
		+	4.After step 3, then you can insert your TF card into M64, and press power button setup M64
		+
		+	===Load your first image on M64 EMMC===
		+	* Run your M64 with TF card
		+	* Copy "xxx-sd-emmc-xxx.img.zip / xxx-sd-emmc-xxx.img" to your USB disk
		+	* Plug your USB disk in M2U
		+	* After M64 recognise USB disk, execute "bpi-copy xxx-sd-emmc-xxx.img.zip / xxx-sd-emmc-xxx.img" to install image on EMMC
		+	* Then power off M64, take TF card out, power on M64
		+
		+	==Advanced Development==
		+	===Update your image===
		+
		+	* execute “bpi-tools”, to update your bpi tools;
		+	* execute “bpi-update -c bpi-m64.conf”, to download new driver to update your image
		+	* execute “file *.tgz”, to check download files’ type is compressed data
		+	* execute “bpi-bootsel”, you will see the bootloader path, “/usr/lib/u-boot/bananapi/bpi-m64/u-boot-with-dtb-bpi-m64-720P-8k.img.gz”
		+	* execute “bpi-bootsel /usr/lib/u-boot/bananapi/bpi-m64/u-boot-with-dtb-bpi-m64-720P-8k.img.gz”, to update your bootloader
		+	* reboot
		+
		+	===How to build uboot & kernel===
		+	====Install tools====
		+	* apt-get udpate
		+	* apt-get install gcc-arm-linux-gnueabihf u-boot-tools
		+	* apt-get install pv
		+	* curl -sL https://github.com/BPI-SINOVOIP/bpi-tools/raw/master/bpi-tools \| sudo -E bash
		+	===Touch screen===
		+	====LCD 7"====
		+	* Execute "bpi-bootsel", you'll see a list of boot files
		+	* Find "BPI_A64_LCD7.img.gz"
		+	* Then execute "bpi-bootsel /usr/lib/u-boot/bananapi/bpi-m64/u-boot-with-dtb-bpi-m64-lcd7-8k.img.gz"
		+	[[Image:A64_bootsel_lcd7.png]]
		+
		+	===GMAC===
		+	Use iperf3 to test gmac
		+
		+	1. On PC Terminal:
		+	* Execute "iperf3 -s"
		+
		+	2. On M2U console:
		+	* TCP test: "iperf3 -c serverIP"
		+	* UDP test: "iperf3 -u -c serverIP"
		+	[[Image:A64_Gmac_test.png]]
		+
		+	===Bluetooth===
		+	* Use bluetoothctl tool to operate BT
		+	* Execute "bluetoothctl"
		+	* If you don't know how to use bluetoothctl, type "help", you will see more commands
		+	* Execute these commands:
		+
		+	[[Image:A64_bluetooth.png]]
		+
		+	===WiFi on A64===
		+	====WiFi Client====
		+	'''You have two ways to setup WiFi Client'''
		+
		+	1. Use commands to setup WiFi client
		+	* ip link set wlan0 up
		+	* iw dev wlan0 scan \| grep SSID
		+	* vim /etc/wpasupplicant/wpa_supplicant.conf
		+	* network={ ssid="ssid" psk="password" priority=1 }
		+	* wpa_supplicant -B -dd -i wlan0 -c /etc/wpa_supplicant/wpa_supplicant.conf
		+	* dhclient wlan0
		+
		+	2. Use UI interface to setup WiFi Client
		+
		+	===Clear boot===
		+	* git clone https://github.com/BPI-SINOVOIP/BPI-files/tree/master/SD/100MB
		+	* bpi-bootsel BPI-cleanboot-8k.img.gz /dev/sdX
		+
		+	===Camara function===
		+	We use HDF5640 camara.
		+
		+	[[Image:ov5640_camara.png]]
		+	====Guvcview====
		+	* Use your UI interface to operate camara
		+	* Applications -> Sound & Video -> guvcview
		+	====Shell====
		+	* We also have built-in command in "/usr/local/bin" to test camara
		+	* "./test_ov5640_image_mode.sh" to test picture taking function
		+	* "./cameratest.sh" to test video recording function
		+
		+	===IR function===
		+	* Execute "getevent"
		+	* Use your IR device to send information to A64
		+
		+	===WringPi===
		+	* GitHub: https://github.com/BPI-SINOVOIP/BPI-WiringPi2.git
		+	* We also have built-in test command in "/usr/local/bin"
		+
		+	====RGB 1602 LCD====
		+	* Execute "/usr/local/bin/bpi_test_lcd1602.sh"
		+
		+	====0.96 Inch OLED Display====
		+	* Execute "/usr/local/bin/bpi_test_52pi.sh"
		+
		+	====8x8 RGB LED Martix====
		+	* Firstly you need a GPIO Extend Board for 8x8 LED Martix
		+	[[Image: WringPi_LED_Martix_Extend_Board.png]]
		+
		+	* Execute "/usr/local/bin/bpi_test_gpio40.sh"
		+
		+	===File System===
		+	* read only system change to read & write mode: "mount -o remount,rw /"
		+
		+	==FAQ==

快速上手 香蕉派 BPI-M64 - Revision history

Sinovoip at 05:51, 27 October 2018

Sinovoip: Created page with "en:Getting_Started_with_M64"

快速上手香蕉派 BPI-M64 - Revision history