Czj: /* Development */

2022-09-22T10:07:55Z

‎Development

Show changes

Sinovoip at 05:23, 27 October 2018

2018-10-27T05:23:59Z

Sinovoip: Created page with "en:Getting_Started_with_M2M"

2018-10-27T05:22:39Z

Created page with "en:Getting_Started_with_M2M"

New page

[[en:Getting_Started_with_M2M]]

← Older revision		Revision as of 05:23, 27 October 2018
Line 1:		Line 1:
	[[en:Getting_Started_with_M2M]]		[[en:Getting_Started_with_M2M]]
		+
		+	=Introduction=
		+	==BPI-M2M==
		+	[[File:M2M_ubuntu.png\|thumb\|Overview: BPI-M2M ubuntu linux]]
		+
		+	Banana Pi M2M is another ARM SoC powered development board that offers great computing performance in an ultra portable form factor. It is a 51mm square with Allwinner A33 Quad-core A7 SoC and 512MB DDR3 RAM.
		+
		+	*Read more about : [[Banana Pi BPI-M2M]]
		+
		+	===Key Features===
		+	* Quad Core ARM Cortex A7 CPU. R16
		+	* 512MB DDR3 SDRAM
		+	* WiFi (AP6212) & Bluetooth onboard
		+
		+	=Development=
		+	==Basic Development==
		+	===Prepare to develop===
		+	* Prepare 8G/above TF card, USB-Serial interface, PC with Ubuntu System
		+	* Using your USB-Serial Connect debug console on M2M
		+
		+	[[Image:M2M__debug_console.png \| 240px]] [[Image:M2M__pin_define.png \| 240px]]
		+
		+	===Compile code===
		+	* git clone https://github.com/BPI-SINOVOIP/BPI-M2M-bsp.git
		+	[[Image:m2m_code.png]]
		+
		+	After download code, execute "./build.sh" to compile it.
		+	* ./build.sh
		+	[[Image:m2m_build.png]]
		+
		+	[[Image:m2m_build_success.png]]
		+
		+	===Update your image===
		+	====Update rootfs & kernal====
		+	After we succeed to the code, Bootloader, kernel, rootfs will be generated in "SD" directory, then how to update the image?
		+
		+	* cd SD/bpi-m2m
		+
		+	[[Image:m2m_code_sd.png]]
		+
		+	Plug in your SD card to Ubuntu PC, then execute "fdisk -l" to check which /dev/sdX were generated by system
		+
		+	[[Image:m2m_code_sd_dev.png]]
		+
		+	* bpi-update -c bpi-m2m.conf -d /dev/sde
		+
		+	[[Image:m2m_bpi_update.png]]
		+
		+	====Update boot====
		+	* cd 100MB
		+
		+	Execute "df -l" to check which /dev/sdX is "BPI-BOOT"
		+	* df -l
		+	[[Image:m2m_df_l.png]]
		+	* bpi-bootsel BPI-M2M-LCD7-8k.img.gz /dev/sd1
		+	[[Image:m2m_bootsel.png]]
		+
		+	===Make your own image===
		+
		+	===Bluetooth===
		+	* Use bluetoothctl tool to operate BT
		+	* Execute "bluetoothctl"
		+	* If you don't know how to use bluetoothctl, type "help", you will see more commands
		+	* Execute these commands:
		+	[[Image:M2M_BT_bluetoothctl.png]]
		+
		+	===WiFi Client===
		+	'''You have two ways to setup WiFi Client'''
		+
		+	1. Use commands to setup WiFi client
		+	* ip link set wlan0 up
		+	* iw dev wlan0 scan \| grep SSID
		+	* vim /etc/wpasupplicant/wpa_supplicant.conf
		+	* network={ ssid="ssid" psk="password" priority=1 }
		+	* wpa_supplicant -i wlan0 -c /etc/wpa_supplicant/wpa_supplicant.conf
		+	* dhclient wlan0
		+
		+	2. Use UI interface to setup WiFi Client
		+
		+	===NAS Application===
		+	1. Usb hub + sata to usb
		+	* HDD is supported
		+	[[Image:M2m_connect_hdd.png]]
		+
		+	[[Image:M2m_connect_hdd_cmd.png]]
		+
		+	* SSD is supported
		+	[[Image:M2m_connect_ssd.png]]
		+
		+	[[Image:M2m_connect_ssd_cmd.png]]
		+
		+	===Camara function===
		+	We use HDF5640 camara.
		+
		+	[[Image:ov5640_camara.png]]
		+	====Guvcview====
		+	* Use your UI interface to operate camara
		+	* Applications -> Sound & Video -> guvcview
		+
		+	====Shell====
		+	* We also have built-in command in /usr/local/bin to test camara
		+	* "./test_ov5640_image_mode.sh" to test picture taking function
		+	* "./cameratest.sh" to test video recording function
		+
		+	===BPI-Tools===
		+	====Install Bpi-tools====
		+	* Execute "curl -sL https://github.com/BPI-SINOVOIP/bpi-tools/raw/master/bpi-tools \| sudo -E bash - "
		+
		+	====Update Bpi-tools====
		+	* Execute "bpi-tools"
		+	[[Image: Bpi-tools.png]]
		+
		+	===RPi.GPIO===
		+	====Install RPi.GPIO====
		+	* Execute "git clone https://github.com/BPI-SINOVOIP/RPi.GPIO"
		+	* after clone the repo, cd RPi.GPIO
		+	* Execute "sudo apt-get update"
		+	* Execute "sudo apt-get install python-dev python3-dev"
		+	* Execute "sudo python setup.py install" or "sudo python3 setup.py install" to install the module
		+
		+	====Using RPi.GPIO====
		+	* cd /usr/local/bin
		+	* Execute "./bpi_test_g40.py" to test RPi.GPIO
		+
		+	[[Image: RPi_GPIO.png]]
		+
		+	===WiringPi===
		+	* GitHub: https://github.com/BPI-SINOVOIP/BPI-WiringPi2.git
		+	* We also have built-in test command in "/usr/local/bin"
		+
		+	====How to Update WiringPi====
		+	* Execute "bpi-update -c pkglist.conf"
		+	[[Image: Update_Pkglist.png]]
		+
		+	* Execute "bpi-update -c bpi-pkg-bpi-wiringpi.conf"
		+	[[Image: Update_WringPi.png]]
		+
		+	====RGB 1602 LCD====
		+	* Execute "/usr/local/bin/bpi_test_lcd1602.sh"
		+	[[Image: WringPi_1602_LCD_m2m.png]]
		+
		+	====0.96 Inch OLED Display====
		+	* Execute "/usr/local/bin/bpi_test_52pi.sh"
		+
		+	====8x8 RGB LED Martix====
		+	* Firstly you need a GPIO Extend Board for 8x8 LED Martix
		+	[[Image: WringPi_LED_Martix_Extend_Board.png]]
		+
		+	* Execute "/usr/local/bin/bpi_test_gpio40.sh"
		+	[[Image: WringPi_LED_Martix_m2m.png]]

快速上手 香蕉派 BPI-M2 Magic - Revision history

Czj: /* Development */

Sinovoip at 05:23, 27 October 2018

Sinovoip: Created page with "en:Getting_Started_with_M2M"

快速上手香蕉派 BPI-M2 Magic - Revision history