Difference between revisions of "Getting Started with M4"

From Banana Pi Wiki
Jump to: navigation, search
(Install Android Image)
(Install Linux Image On M4)
Line 35: Line 35:
=Development For Linux=
=Development For Linux=
===Install Linux Image On M4===
===Install Linux Image===
Download the latest [https://download.banana-pi.dev/d/3ebbfa04265d4dddb81b/?p=%2FImages%2FBPI-M4%2Flinux&mode=list Linux image]  
Download the latest [https://download.banana-pi.dev/d/3ebbfa04265d4dddb81b/?p=%2FImages%2FBPI-M4%2Flinux&mode=list Linux image]  

Revision as of 20:13, 26 July 2020



Overview:Realtek RTD1395
 Banana Pi BPI-M4 use Realtek RTD1395 chp design ,it is a 64-bit quad-core A53 mini single board computer. It features 1 GB of RAM and 8 GB eMMC. It also has onboard WiFi for b/g/n/ac and BT 4.2. On the ports side, the BPI-M4 has 4 USB 2.0 ports, 1 USB TYPE C port, 1 HDMI port, 1 audio jack. support M.2 Key E PCIE 2.0 interface. 

Key Features

  • Realtek RTD1395 ARM Cortex-A53 Quad-Core 64 Bit
  • Mali 470 MP4 GPU OpenGL ES 1.1/2.0 H.264 H.265,2K4K
  • Onboard1 GB DDR4 (option 2 GB)
  • 8G eMMC flash (max 64 GB)
  • 10/100 Mbit/s Ethernet and RTL8821 module support Wi-Fi 802.11 b/g/n/AC + Bluetooth 4.2
  • USB 2.0 TYPE C
  • M.2 Key E slot PCIE 2.0 and USB 2.0
  • PoE function support

Development For Android

Install Android Image

Download the latest android image

Download BPI-M4 USB flash tool


 1. BPI-M4 Android8 image only support 2GB ddr board.
 2. BPI-M4 USB flash tool is a usb download tool for flashing android image to board emmc, and only support Windows platform.
 3. Make sure SW2 (board bottom near sd slot) switch to '1' for emmc boot.
 4. Read document/bananapi_m4_usb_download_tool_guide.doc before flashing image.

Development For Linux

Install Linux Image

Download the latest Linux image

1. Board SW2 switch to 0 for sd boot
2. For the compatibility of new 2GB and 1GB board with one Linux image, the old batch (before May, 2020) 1GB board must update the spirom firmware, so it can run the new release image.

Install Image to SD Card On Linux PC with bpi-tools

1.Install bpi-tools on your linux
    $ apt-get install pv
    $ curl -sL https://github.com/BPI-SINOVOIP/bpi-tools/raw/master/bpi-tools | sudo -E bash
2.Insert your TF card into your PC
    $ bpi-copy xxx.img /dev/sdx

Install Image to SD Card with Etcher on Windows, Linux and MacOS

Balena Etcher is an open source project by Balena, Flash OS images to SD cards & USB drives

Install Image to EMMC with SD Ubuntu

1.Prepare a sd which is installed ubuntu image and bootup with sdcard
2.Copy emmc image to udisk, plug in board, then mount udisk.
3.After mount udisk, use command "bpi-copy xxx-emmc-xxx.img" to install image on Emmc.
4.After success install, power off the board, eject the sdcard and poweron with emmc boot.

Installed Docker

To have a test, if docker has installed in your image.

  • sudo docker run --rm hello-world


Use iperf3 to test gmac

1. On PC Terminal:

  • Execute "iperf3 -s"

2. On M3 console:

  • TCP test: "iperf3 -c serverIP"
  • UDP test: "iperf3 -u -c serverIP"

M4 Emac test.jpg


You have two ways to setup BT

1. Use commands to setup BT

  • Use bluetoothctl tool to operate BT
  • Execute "bluetoothctl"
  • If you don't know how to use bluetoothctl, type "help", you will see more commands
  • Execute these commands:

M4 bluetooth.jpg

2. Use UI interface to setup BT

WiFi on M4

WiFi Client

You have two ways to setup WiFi Client

1. Use commands to setup WiFi client

  • ip link set wlan0 up
  • iw dev wlan0 scan | grep SSID
  • vim /etc/wpa_supplicant/wpa_supplicant.conf
  • wpa_supplicant -iwlan0 -c /etc/wpa_supplicant/wpa_supplicant.conf
  • dhclient wlan0

2. Use UI interface to setup WiFi Client

M4 WiFi iperf3.jpg