Difference between revisions of "Banana Pi BPI-F2"

From Banana Pi Wiki
Jump to: navigation, search
(Hardware spec)
 
(19 intermediate revisions by one other user not shown)
Line 1: Line 1:
 +
[[zh:香蕉派_BPI-F2]]
 
=Introduction=
 
=Introduction=
  
 
[[File:BPI-F2_1.JPG|thumb|Overview:BPI-F2 with freescale IMX6]]
 
[[File:BPI-F2_1.JPG|thumb|Overview:BPI-F2 with freescale IMX6]]
 
[[File:BPI-F2_2.JPG|thumb|Overview:BPI-F2 with freescale IMX6]]
 
[[File:BPI-F2_2.JPG|thumb|Overview:BPI-F2 with freescale IMX6]]
 +
 +
Banana Pi BPI-F2 use freescale IMX6 Industrial chip design. IMX6 with ARM Cortex-A9 MPCore 4xCPU processor(with TrustZone),this is ths first banana pi board design with freescale chip.
 +
 +
[[File:BPI-F2.jpg]]
  
 
==Key Features==
 
==Key Features==
 +
* freescale IMX6 Industrial solutions.
 +
* 2G DDR3 and 8G eMMC flash
 +
* CAN bus function support
 +
* Mini PCIE interface
 +
* 2 camera interface:DVP and MIP
  
 
==Getting Start==
 
==Getting Start==
Line 10: Line 20:
 
=Hardware=
 
=Hardware=
 
==Hardware interfact==
 
==Hardware interfact==
 +
 +
[[File:BPI-F2_interface.JPG]]
  
 
==Hardware spec==
 
==Hardware spec==
Line 16: Line 28:
 
| style="background: PaleTurquoise; color: black" colspan="4"| '''HardWare  Specification of Banana pi BPI-F2'''
 
| style="background: PaleTurquoise; color: black" colspan="4"| '''HardWare  Specification of Banana pi BPI-F2'''
 
|-
 
|-
|Soc ||  with freescale IMX6
+
|Soc ||  freescale IMX6
 +
|-
 +
| CPU || ARM Cortex-A9 MPCore 4xCPU processor(with TrustZone)
 +
|-
 +
| GPU || OpenGL ES 2.0 3D graphics accelerator with forshaders,2D graphics accelerator,and didicated OpenVG 1.1 accelerator
 
|-
 
|-
| CPU ||  
+
| SDRAM || 2G DDR3
 
|-
 
|-
| GPU ||
+
| PCIE|| 1 mini PCIE interface
 
|-
 
|-
| SDRAM ||
+
| CAN bus || 1 CAN bus interface
 
|-
 
|-
 
| SATA || support 1*SATA interface  
 
| SATA || support 1*SATA interface  
Line 28: Line 44:
 
| GPIO || 40 Pins Header, 28×GPIO, some of which can be used for specific functions including UART, I2C, SPI, PWM, I2S.  
 
| GPIO || 40 Pins Header, 28×GPIO, some of which can be used for specific functions including UART, I2C, SPI, PWM, I2S.  
 
|-
 
|-
| On board Network || 10/100/1000Mbps Ethernet \(Realtek RTL8211E/D\)
+
| On board Network || 10/100/1000 Mbit/s Ethernet  
 
|-
 
|-
| Wifi Module || WiFi 802.11 b/g/n \(AP 6212 module on board\)
+
| Wifi Module || N/A
 
|-
 
|-
| Bluetooth || BT4.0
+
| Bluetooth || N/A
 
|-
 
|-
| On board Storage || MicroSD \(TF\) card,No eMMC onboard  
+
| On board Storage || MicroSD \(TF\) card,8G eMMC onboard (option 8-64G)
 
|-
 
|-
| Display || 4-lane MIPI DSI display,or RGB panel or LVDS panel,TV-out on HDMI V1.4
+
| Display || HDMI out, LVDS out
 
|-
 
|-
| Video || Multi-format FHD video decoding, including Mpeg1/2, Mpeg4, H.263, H.264, etc H.264 decode up to 1080P60,support video encodeing:High-deinition\(HD\)H.264 video encoder is up to 1080P@45fps
+
| Video || HDMI out, LVDS out
 
|-
 
|-
| Audio outputs || HDMI, analog audio \(via 3.5 mm TRRS jack\), I2S audio \(also potentially for audio input\)
+
| Audio outputs || 1 * 3.5 headset jack  
 
|-
 
|-
| Camera || A CSI input connector Camera:Supports 8-bit YUV422 CMOS sensor interface,Supports CCIR656 protocol for NTSC and PAL,Supports 5M pixel camera sensor ,Supports video capture solution up to 1080p@30fps
+
| Camera || 1 * DVP camera interface and 1* MIP camera interface
 
|-
 
|-
| Audio input || On board microphone
+
| Audio input || N/A
 
|-
 
|-
| USB || 4 USB 2.0 host, 1 USB 2.0 OTG
+
| USB || 2 * USB 2.0 1* USB Otg
 
|-
 
|-
| Buttons || Reset button, Power button, U-boot button
+
| Buttons || Power & Reset
 
|-
 
|-
| Leds || Power status Led and RJ45 Led
+
| Leds || 3* RGB leds
 
|-
 
|-
| IR || No onboard IR receiver
+
| IR || N/A
 
|-
 
|-
| DC Power || 5V/2A with micro USB port  
+
| DC Power || 12V/2A with DC port  
 
|-
 
|-
 
| battery || No 3.7V lithium battery power support
 
| battery || No 3.7V lithium battery power support
 
|-
 
|-
| Sizes || 85mmX56mm,same size as raspberry pi 3
+
| Sizes ||  
 
|-
 
|-
| Weight || 40g
+
| Weight || 80g
 
|-  
 
|-  
 
|}
 
|}
 +
 +
=Resources=
 +
==Documents==
 +
 +
IMX.6 wiki page : https://en.wikipedia.org/wiki/I.MX#i.MX_6_series
 +
 +
==Source code==

Latest revision as of 19:46, 11 October 2018

Introduction

Overview:BPI-F2 with freescale IMX6
Overview:BPI-F2 with freescale IMX6

Banana Pi BPI-F2 use freescale IMX6 Industrial chip design. IMX6 with ARM Cortex-A9 MPCore 4xCPU processor(with TrustZone),this is ths first banana pi board design with freescale chip.

BPI-F2.jpg

Key Features

  • freescale IMX6 Industrial solutions.
  • 2G DDR3 and 8G eMMC flash
  • CAN bus function support
  • Mini PCIE interface
  • 2 camera interface:DVP and MIP

Getting Start

Hardware

Hardware interfact

BPI-F2 interface.JPG

Hardware spec

HardWare Specification of Banana pi BPI-F2
Soc freescale IMX6
CPU ARM Cortex-A9 MPCore 4xCPU processor(with TrustZone)
GPU OpenGL ES 2.0 3D graphics accelerator with forshaders,2D graphics accelerator,and didicated OpenVG 1.1 accelerator
SDRAM 2G DDR3
PCIE 1 mini PCIE interface
CAN bus 1 CAN bus interface
SATA support 1*SATA interface
GPIO 40 Pins Header, 28×GPIO, some of which can be used for specific functions including UART, I2C, SPI, PWM, I2S.
On board Network 10/100/1000 Mbit/s Ethernet
Wifi Module N/A
Bluetooth N/A
On board Storage MicroSD \(TF\) card,8G eMMC onboard (option 8-64G)
Display HDMI out, LVDS out
Video HDMI out, LVDS out
Audio outputs 1 * 3.5 headset jack
Camera 1 * DVP camera interface and 1* MIP camera interface
Audio input N/A
USB 2 * USB 2.0 1* USB Otg
Buttons Power & Reset
Leds 3* RGB leds
IR N/A
DC Power 12V/2A with DC port
battery No 3.7V lithium battery power support
Sizes
Weight 80g

Resources

Documents

IMX.6 wiki page : https://en.wikipedia.org/wiki/I.MX#i.MX_6_series

Source code