Difference between revisions of "BPI-PC101 gesture recognition module"

From Banana Pi Wiki
Jump to: navigation, search
(Principles of Operation)
(Principles of Operation)
Line 196: Line 196:
  
 
This address holds the distance of the gesture from 0 to 255, the larger is near, the smaller is far.
 
This address holds the distance of the gesture from 0 to 255, the larger is near, the smaller is far.
 +
 +
=How to Start=
  
 
=Documents=
 
=Documents=

Revision as of 04:44, 27 June 2018

Introduction

The PC101 integrates an ambient light (ALS) sensor, a proximity sensor (PS) and 6-D gesture sensors with built-in IR LED. It is used in notebook PCs, smartphones, MIDs (mobile internet devices),PNDs (portable navigation devices), e-books, tablet PCs, flat-panel televisions, etc. for extending battery life and for better user experience. Ambient light sensor optimizes the screen brightness to extend battery and to increase battery life. Proximity sensor (PS) measures the IR reflection intensity which correlates to the distance of the object. Proximity sensor enables the device controller to turn off the LCD back-light and the touch-screen sensor when the device is held close to your ear, placed inside the pocket, purse, or bags. This function saves the battery power and avoids unintended touch-screen trigger. Proximity sensor can also work as a device wake-up sensor by sensing the user waving the hand in front of the device. The 6-D gesture sensor detects the waving of palm in front of the screen in 6 directions left, right, up, down and z-axis. The hand gesture without the need to touch the screen adds new way of human device interaction. For example, the gesture can be used to accept a phone call in the hand-free mode while the user is driving in a car. In another example, the user wave to the screen to advance or retract in the picture viewing mode without worrying the food stains from the fingers to be left on the screen.

Key Features

  • Digital control and data output via I2C (100 KHz and 400 KHz) interface
  • ALS, PS and Gesture sensor with built-in IR LED
  • Slave Address 0x58
  • 6D Gesture Recognition Distance: 20~200 mm(up、down、left、right、hold)
  • Programmable interrupt function for ALS and PS with upper and lower thresholds
  • Support interrupt notification

Applications

  • smart lights
  • Household electrical control
  • Music control equipment
  • Game equipment
  • Smart bath
  • Distance detection
  • Smart toy

Hardware

Interface

Pc101 interface.jpg

Block Diagram

Pc101 block.png

PC101 DFN Pin Assignment

Pc101 1.png

Hardware spec

PC101 PIN definitions

PC101 Gesture Sensor Pin define
Pin Name Description
1 5V Power
2 GND Ground
3 INT Digital Out
4 SCL Serial Digital Input Clock
5 SDA Serial Digital I/O Data
6 TXD Serial port sends pins
7 RXD The serial port receives the pin

Application Circuit

Pc101 2.png

Electrical Characteristics

  • Voltage characteristic
Voltage characteristic
No pin MIN TYP MAX UNIT
1 5V 4.5 5.0 5.5 V
2 GND -0.3 0 0.3 V
3 INT GND 0/3.3 3.7 V
4 SCL -0.3 0/3.3 3.7 V
5 SDA -0.3 0/3.3 3.7 V
  • Digital interface characteristics
Digital interface characteristics
No Description MIN TYP MAX UNIT
1 SCL/SDA:LOW -0.3 - 1.0 V
2 SCL/SDA:HIGH 2.3 - 3.6 V
3 SCL 0 - 400 kHz
4 Pull-up resistors - 2.0 -
5 INT:LOW - - 0.4 V
6 INT:HIGH 2.4 - - V

I2C interface

I2C interface '
Ordering Chip Information Write to Slave Read from Slave
PC101 1011000 1011001
  • Receive (Single Read) data from register

Pc101 3.png

  • Send (Single Write) data into register

Pc101 4.png

Principles of Operation

Total register addresses are maintained inside the I2C block, each having a 8-bit register address. Each address accommodates an 8-bit data register that can be either written or read via I2C. The command registers program the sensor for various modes, setting and Interrupt threshold. The read-only registers contains output codes.

  • Register Table and Definitions
Register Table and Definitions
NAME R/W 8-bit Address Default Descrition
ChipID R 0x00 0xAA Chip ID
Capability R 0x01 0xF0 Gesture Functional description
LibVersion R 0x02 0xB1 Gesture Version
Gesture R 0x03 0x00 Gesture Data
Proximity R 0x04 0x00 Distance
  • 0x00: ChipID

This address holds ChipID, which is 0xAA by default and can be read to verify that I2C reading is normal.

  • 0x01: Capability

This address holds a bitmap of the gesture detection capability, 0 Disable, 1 enable.

Digital interface characteristics
BIT 7 6 5 4 3 2 1 0
Read Proximity Hold Left/Right Up/Down Reserved Reserved Reserved Reserved
Reset 1 1 1 1 0 0 0 0

The default is all supported, so the register defaults is 0xF0.

  • 0x02: LibVersion

This address holds Gesture Version defaults is 0xB1.

  • 0x03: Gesture Date

The address is stored with the result of gesture detection.

address of gesture detection
0: Gesture(Hold) 0xA0
1: Gesture(Up) 0xA1
2: Gesture(Down) 0xA2
3: Gesture(Left) 0xA3
4: Gesture(Right) 0xA4
  • 0x04: Proximity Date

This address holds the distance of the gesture from 0 to 255, the larger is near, the smaller is far.

How to Start

Documents